Supported Hardware

Devices, command stations, networks, and protocols:

• Anyma DMX
• Arduinos
• Atlas Commander
• Bachrus
• BiDiB
• CAN Bus Networks
• CBUS®
• C/MRI
• CTI Electronics (Acela)
• CVP EasyDCC
• Dcc4Pc
• DCC-EX EX-CommandStation
• DCC++
• DCC Specialities
• Digi XBee
• Digikeijs (Digirails)
• Digitrax
• DMX 512 (Powerline)
• ESU ECoS
• Fleischmann
• Hornby
• Insteon (Powerline)
• Lenz
• Lionel TMCC
• LocoNet
• Maple Systems
• Märklin CS2
• MERG
• Modbus
• MQTT
• MRC
• NAC Services RPS
• NCE
• Oak Tree Systems
• OpenDCC
• OpenLCB
• Pi Engineering RailDriver
• Powerline
• Protrak Grapevine
• QSI Quantum Programmer
• Raspberry Pi
• RFID Readers
• Roco
• SPROG DCC
• SPROG DCC Generation 5
• SRCP server
• TAMS Master Control
• TracTronics SECSI
• Uhlenbrock Intellibox
• Viessmann Commander
• Wangrow System One
• WiFi Throttles
• X10 (Powerline)
• XPressNet
• Zimo MX-1
• ZTC Controls

Applications

By the community of JMRI.org:

• DecoderPro®
• PanelPro™
• DispatcherPro™
• OperationsPro™
• SoundPro™
• Apps with JMRI connections...
• Jython Apps for JMRI...
• FAQ

Tools

JMRI tools for working with your layout:

• Common Tools:
  • Throttles
  • Turnouts
  • Lights
  • Sensors
  • Signaling
  • Consisting
  • Reporters
  • Memory Variables
• Blocks:
  • Blocks
  • Sections
  • Transits
• Routing and Control:
  • Routes
  • LRoutes
  • Entry Exit (NX)
  • Logix
  • LogixNG
• Other:
  • Audio
  • CTC Tools
  • Fast Clocks
  • ID Tags
  • Speedometer
  • Timetable
  • Virtual Sound Decoder
  • Where Used
  • Permissions
• System-specific...
• Web server tools...

Layout Automation

Use JMRI to automate parts of your layout and operations:

• Signaling
• Warrants
• Dispatcher
• Routes
• LRoutes
• Entry/Exit Routing
• Logix
• LogixNG
• Scripting
• Automate with Java
• CTC Tools

Donate to JMRI.org

Hardware Support: SPROG Generation 5 Hardware

• Pi-SPROG 3
• SPROG 3 plus
• Pi-SPROG 3 plus
• CANISB
• Hardware Setup with JMRI
• Documentation
• Support

Pi-SPROG 3

Available as a firmware upgrade to the original Pi-SPROG One, the Pi-SPROG 3 turns a Raspberry Pi module into a fully fledged stand-alone DCC programmer and command station.

SPROG 3 Plus and Pi-SPROG Plus

DCC command stations and programmers with integrated CBUS® adapters (no need for a separate USB - CAN adapter) and dual track outputs.

Features

• Two track outputs allow simultaneous running and programming.
• Main track output up to 2.5 Amps
• Flexible second track output features:
  • Up to 2.5 Amp output
  • Can be disabled when not programming
  • Can follow main track output when not programming allowing locos to be driven onto an isolated programming track.
  • Can be used as an auto-reverse power district output (no service mode programming available in this mode.
• CAN interface (to be enabled in a future firmware release) for full CBUS connectivity.

CANISB Isolated USB CAN adapter

A electrically isolated USB CAN adapter that removes any electrical connection between the host computer's USB interface and the CBUS network.

Hardware Setup with JMRI

Create a new profile. The example shown is for Pi-PSROG 3 hardware. Enter the name and click OK.

Select the New Profile and click OK

Click Next when the Wizard appears.

Make the following selections:

• System Manufacturer: SPROG DCC Generation 5
• System Connection: Select your hardware, e.g., showing Pi-SPROG 3
• Serial Port: Selection will depend on host computer and operating system

Click Next to complete the setup.

CBUS is a registered trade mark of Dr Michael Bolton

---