Decoder Family: Stationary Decoder

CV Definitions:

CVNamePositionsValues
1VVVVVVVV
    2XVVVVVVV
      3XVVVVVVV
        5VVVVVVVV
          7XXXXXVVV
          1. None
          2. Restart the Servette
          3. Move servos to center position
          4. Move servos back and forth
          5. Move servos to one end
          6. Move servos to the other end
          7
            8
              10XVVVVVVV
                11XVVVVVVV
                  12VVVVVVVV
                    14VVVVVVVV
                      16VVVVVVVV
                        18VVVVVVVV
                          20VVVVVVVV
                            22VVVVVVVV
                              24VVVVVVVV
                                26VVVVVVVV
                                  29XXXXXVVV
                                  1. Mode 1 - Servo 2 Pos, output 2 has unique address
                                  2. Mode 2 - Servo 2 Pos, output 2 has servo address
                                  3. Mode 3 - Servo 3 Pos, output 2 has unique address
                                  4. Not used -do not select
                                  5. Mode 4 - Inputs control servo, output 2 has unique address
                                  29XXXXVXXX
                                    29XXXVXXXX
                                      29XXVXXXXX
                                        31XVVVVVVV
                                          33XXXXXXVV
                                          1. b
                                          2. t
                                          3. c
                                          34XXXXXXVV
                                          1. t
                                          2. c
                                          36XXXXXXVV
                                          1. Input Disabled
                                          2. On Low to High Transition
                                          3. On High to Low Transition
                                          4. On Change Transition
                                          36VVVVXXXX
                                            36XXXXVVXX
                                            1. Close
                                            2. Throw
                                            3. Toggle
                                            44XXXXXXVV
                                            1. Input Disabled
                                            2. On Low to High Transition
                                            3. On High to Low Transition
                                            4. On Change Transition
                                            44VVVVXXXX
                                              44XXXXVVXX
                                              1. Close
                                              2. Throw
                                              3. Toggle
                                              67XVVVVVVV
                                                71XXXXXXVV
                                                1. None
                                                2. Sequence or rotate
                                                3. Speed to Position
                                                71VXXXXXXX
                                                  75XXXXXXVV
                                                  1. None
                                                  2. Will flash when servo is in the cw position
                                                  3. Will flash when servo is in the ccw position
                                                  Basic ------ Servette Output Addresses ------ Use this number to set the address number of the device the output is connected to. ------ Special Functions ------ This is the same as a Loco address ------ Notes: ------ The Custom Programmer format is recommended Mfg ---- Sets the Servette to a particular test state - Use to help adjust servos ---- Only works in Ops mode Changes the value of CV7 (Version ID) as displayed in DP Test State may change when Version ID is read Inputs ------ Primary Input Control 1 ------ ------ Secondary Input Control 1 ------ Outputs ---- Servo Configuration ---- ---- Output Flashing ---- ---- Sets the output state to always be the same at power on ---- Only applies if Option 1 is selected Servette Both Throw Close Relay Throw Close Routes ---- Remote Control Route Address ---- CVs
                                                  This page was produced by JMRI.

                                                  Copyright © 1997-2024 JMRI Community.

                                                  JMRI, DecoderPro, PanelPro, DispatcherPro and associated logos are our trademarks.

                                                  Additional information on copyright, trademarks and licenses is linked here.